36 Site Supervision jobs in Houston

ABOUT THE ROLE


To obtain and monitor, by chemical and physical tests, representative samples from the Production Department of raw materials, feed, clinker and cement, and advise them of adjustments to ensure a quality product with a minimum of variations.

WHAT YOULL BE DOING

• Analyze raw mix with X-ray, wet or physical analysis and instruct Raw Grind on change, and assist in solving any problems.


• Monitor clinker production with X-ray or wet analysis and insure quality clinker used in cement production.


• Monitor cement production with X-ray, wet or physical analyses and oversee adjustments to proportions, admixtures, fineness and air content, assist in solving any problems.


• Record accurately and timely, data for use by management and other departments.


• Perform complete ASTM chemical and physical test on daily composite samples to insure product meets strict plant standards.


• Perform periodic calibration and preventive maintenance checks on all equipment and maintain chemical solutions.


• Run proficiency samples against other labs.


• Take inventories of gypsum and admixtures.


• Perform microscopic evaluation of cement and clinker.


• Run heat content on calorimeter.

• Demonstrate a commitment to communicating, improving and adhering to health, safety and environmental policies in all work environments and areas. Promote a culture of safety and exhibit these behaviors.


• Successful candidates must adhere to all safety protocols and proper use of Amrize approved Personal Protection Equipment ("PPE"), including but not limited to respirators. Employees that are required to wear respirators must be clean shaven where the respirator seal meets the face in order to pass the qualitative and quantitative fit tests.

• Competitive salary


• Retirement Savings: Choose from 401(k) pre-tax and/or Roth after-tax savings


• Medical, Dental, Disability and Life Insurance


• Holistic Health & Well-being programs


• Health Savings Accounts (HSAs) & Flexible Spending Accounts (FSAs) for health and dependent care


• Vision and other Voluntary benefits and discounts


• Paid time off & paid holidays


• Paid Parental Leave (maternity & paternity)


• Educational Assistance Program


• Dress for your day

We are looking for a Quality Control Technician for our Stafford, Texas operation.  This company is a master distributor of industry recognized valves. If you have the first to arrive and last to leave attitude, then we need to talk.

JOB SUMMARY
The ideal candidate for the Quality Control Technician role should exhibit strong organizational skills, attention to detail, and an ability to work efficiently in a fast-paced environment. Effective communication is crucial, both in writing and orally, along with active listening skills. The candidate should be self-motivated and independent while maintaining a collaborative, team-oriented approach. Problem-solving abilities and a quick-learning disposition are key. A sense of responsibility and a proactive attitude towards troubleshooting challenges are essential traits.
The candidate should also demonstrate adaptability and versatility, particularly in cross-functional tasks such as collaborating with the Order Picking team. Overall, the successful candidate will contribute to the efficient functioning of the quality management system through a combination of skills, responsibility, and effective communication.
 
PRIMARY RESPONSIBILITIES

• Verify that all QC/QA requirements are met, maintain electronic logs, complete electronic inspection reports, and electronic rejection reports, as necessary.
• Learn the inventory and become an expert regarding it.
• Identify areas of improvement within the inspection process to enhance order accuracy.
• Inspect outbound orders and assist in inspection for inbound orders.
• Cross-train among other Warehouse Jobs such as Picking and Receiving. 
• Other tasks as assigned.

• 1+ Years of on-the-job experience in mechanical or Valve inspection.
• A High School diploma or GED.

• Ability to accurately count components by hand or via weight counting.
• Ability to read and understand purchase orders, material test reports (MTR), and material specifications.
• Ability to gain a working knowledge of quality standards such as API and Trim Charts.
• Ability to establish and maintain constructive working relationships with people.
• Strong problem-solving and analysis skills.
• Ability to manage multiple tasks and projects daily in a fast-paced distribution environment.
• Able to work independently or as part of a team on a broad variety of projects.
• Willingness to work additional hours to meet tight deadlines.
• Able to follow directions and very detail oriented.
• PPE required - Steel Toeboots.

• Perform incoming inspections on purchased parts, subassemblies, and finished products to ensure compliance with engineering drawings and customer standards.
• Review Material Test Reports (MTR) and Certificates of Conformance (CofC) against relevant standards.
• Analyze Non-Conformance Reports (NCR) to identify trends and generate Corrective Action Reports (CAR) as needed.
• Create Non-Conformance Reports and other departmental reports as assigned.
• Evaluate issues and make initial recommendations for corrective actions to supervisors.
• Investigate failures to determine root causes and propose remedial actions.

• Minimum of four years' experience in quality control within the industrial manufacturing sector.
• Experience with Positive Material Identification (PMI) preferred.
• Proficient in computerized record-keeping and standard software applications.
• Strong written and verbal communication skills.
• Skilled in using and calibrating precision measuring equipment (e.g., micrometers, height gauges, calipers, dial indicators, bore gauges).
• Knowledge of ISO 9001:2008/2015 and API standards.
• Ability to analyze and determine the best inspection methods for product conformity.
• Proficient in interpreting engineering drawings and understanding Geometric Dimensioning and Tolerancing (GD&T).
• Experience with Coordinate Measuring Machines (CMM).
• Ability to manage multiple tasks in a fast-paced environment while meeting delivery requirements.
• High School Diploma or equivalent required.

• Must have 20/20 vision (correctable) without color blindness.
• Ability to lift up to 20 pounds.

• Career Growth: We offer numerous opportunities for advancement within the organization.
• Comprehensive Benefits: Enjoy benefits such as:
  • Life, medical, dental, and vision insurance
  • Paid holidays and vacation
  • 401(k) plan with matching contributions
• Healthy Work Environment: We provide a smoke-free, drug-free workplace to ensure a safe and productive atmosphere.

About Us:Panelmatic, Inc. was founded in 1957 in Youngstown, OH to serve manufacturing industries with the design and build of custom electrical, instrument, and pneumatic control panels. Our business has sufficiently grown over the years to support expansion for our clients. We have produced control packages for many of America's top corporations in the chemical, environmental, food, pulp and paper, rubber, petroleum, pharmaceutical, glass, metals, and utility industries. We also deliver equipment for use worldwide. Our rigorous methodology assures compliance with domestic and international standards. We can meet the needs of our diverse clientele from start to finish through sales, design, fabrication, testing, and delivery.Since 1957, we have been known for our high-quality, custom-built control packages, our comprehensive service, and our technological and manufacturing expertise. This expertise assures you of our ability to handle the largest and most complex packages quickly and efficiently.Job Summary:Panelmatic is seeking a detail-oriented experienced Quality Control Inspector. In this role, you'll play a key role in ensuring that all products meet our established requirements for reliability and workmanship, as well as other quality control program standards.Job Duties: Inspecting output samples using industry-appropriate methods, such as comparing to standards, measuring dimensions, and examining functionality, as well as electrical testing as required. Checking that the assembly or production line adheres to standards and procedures and complies with legal requirements Reviewing blueprints, electrical schematics, and specifications to compare to produced goods and generating an inspection report to document all deviations. Recording inspection results by completing reports, summarizing re-works and wastes, and inputting data into a quality database Assist in training the production team on quality control measures to improve product excellence Proposing improvements to the production process Monitoring the use of equipment to ensure it is safe and discard any that do not meet requirements Updating job knowledge by engaging in educational opportunities and regular training Keeping measurement equipment operating accurately by following calibration requirements and calling for repairs Reading and interpreting engineering drawings and electrical schematics. Comprehension and operation of basic electrical measuring equipment. Collecting and compiling statistical quality data Assisting in the development of test methods and inspection plans Determining the causes of product defects and reworks Verifying all equipment is calibrated correctly Understanding the functionality of basic electrical components for use in industrial electrical cabinets/panels. Coordination and Support of customers during the FAT process. RequirementsMinimum Qualifications: Associates degree required One year of experience with electrical inspection and testing required Good written and verbal communication skills required Excellent problem-solving and analytical skills required Keen attention to detail required Basic computer and math skills to calibrate and measure specifications required Ability to use measuring devices such as gauges, meters, calipers, and computers required In-depth understanding of company standards required Up-to-date knowledge of federal and industry standards, UL codes, and best practices required Understanding of target market and consumer needs required Blueprint and electrical schematic reading capabilities required Documentation and reporting skills required Teamwork and collaboration required Growth mindset with the ability to accept challenges required Ability to pass physical, drug, driving, and background check required Ability to physically push, pull, and lift 50lbs or more required Ability to sit, stand, and walk for four-plus hours at a time required Alignment with company core values required Preferred Qualifications: Two plus years of experience with electrical inspection and testing preferred A BS in Engineering or equivalent work experience preferred Experience in an ISO environment preferred Experience in Lean/Six sigma preferred BenefitsBenefits: Medical, dental, vision, HSA, term life, AD&D, STD, LTD 100% medical premium paid for by Panelmatic for the employee-only level medical coverage 80% paid for by Panelmatic and 20% paid for by the employee on all other level medical coverage (i.e. employee plus child, employee plus spouse, family) 401K and bonus Scholarships, educational reimbursement, paid volunteerism, and paid personal and professional development provided PTO and paid holidays provided Career advancement opportunities Competitive wages Family-friendly environment with average employee tenure above five years

MINIMUM 1 YEAR OF EXPERIENCE AS A QC INSPECTOR. Connect Staffing is looking for an experienced QC Inspector for a drilling equipment manufacturer company in North Houston, TXSchedule: Monday - Friday 5:00am-5:30pmRequirements of the QC Inspector:At least 1 year of related experience as a QC Inspector.Pass a drug screen, physical, and background check.Ability to read, analyze, and interpret general business periodicals, professional journals, technical procedures, or governmental regulations.Ability to effectively present information and respond to questions from groups of managers, clients, customers, and the public.Knowledge of Word Processing software; Design software; Order processing systems; Manufacturing software and Database software.Ability to do basic math functions. Must be able to safely lift objects up to 25 lbs.Prior experience in roles such as a Quality Assurance Inspector, Quality Technician, Quality Control Technician, Quality Assurance Technician, or QA/QC Analysis a big plus!Benefits:Affordable health and dental plansReferral ProgramWeekly OTPotential to get hired as a full-time employee.Responsibilities of the QC Inspector: Inspect products for compliance with order specifications, legal requirements, and quality standards.Approve or reject products and document examination results.Perform precise measurements, including angles, radii, contours, and surface finishes, using various instruments.Test parts for hardness and verify accuracy of gauges and measuring tools.Prepare and maintain job tickets, labor cards, inspection reports, and related documentation.Ensure productivity standards are met while maintaining a clean and orderly work area.Follow all Good Manufacturing Practices (GMP), safety protocols, and ensure safety equipment is in use and operational.Interact professionally with team members to support a collaborative work environment.All candidates meeting the minimum requirements will receive an SMS invite to an AI-based interview. This interview helps us understand your qualifications and experience, and candidates who complete it will receive first consideration. Please expect a text message from ( within 30 minutes of submitting your application.See all our current openings and waitlists at jobs.connectstaffing.com !#CONHP

• Micrometers, calipers, Multimeter.
• Reading and interpretation of engineering drawings and specifications.
• Computer skills, including familiarity with Microsoft Word and Excel.
• Strong communication skills, both verbal and written.
• Experience in use of and/or programming of automated inspection tools, such as vision inspection systems.
• Experience working in an ISO 9001 manufacturing environment.

• High school diploma or equivalent (two years of college preferred)
• OR, 3 to 5 years' experience in a manufacturing environment as a quality control inspector/technician.
• (Required) IPC Certified Quality Inspector.