3,210 Ndt Technician jobs in the United States

Non Destructive Testing (NDT) Technician

Company : Safran Helicopter Engines

Job field : Manufacture / assembly and repair

Location : Grand Prairie , Texas , United States

Contract type : Permanent

Contract duration : Full-time

Required degree : High School Diploma/GED Equivalent

Required experience : More than 3 years

Professional status : Technician

Salary range : TBD

# 2025-159294

Apply with one click Any questions ?

Job Description

Summary of Job Purpose:

Perform Non Destructive special processes on the Safran Helicopter family of engines.

Job Duties:

Production Means – NDT

• Perform the NDT inspection of isolated engine component parts to identify discontinuities for further evaluation in accordance with the repair and overhaul manual specifications.

• Possess or acquire the skills and knowledge to setup and standardize the equipment, process parts, interpret and evaluate the resulting indications and document results.

• Ensure thorough familiarity with the scope and limitations of the techniques/methods being applied within one's current qualification applicable to one or all of the following NDT disciplines: FPI, MPI, Eddy Current, and/or Ultrasonic.

Cost

• Continuously improve one's ability to perform processes within the established efficiency standards.

• Strive for an individual LUR average greater than 90% all the while meeting the designated time standards set for the processes to be performed.

Quality

• Ensure that work performed complies with the company's quality standards and regulatory requirements.

• Inform the area Manager or Master Tech of any deviation that may have occurred during the application of the process.

• All work performed must be documented on the appropriate paperwork, electronic schedules, and within the organization's ERP system.

Safety

• Wear all the identified PPE as required and respect the documented safety procedures.

• Maintain the working area in a clean and organized condition respecting the 5s methodology established.

Innovation:

• Identification of improvement ideas to improve efficiency and reduce cost within current processes

• Active participation in improvements within the area such as 5s and other workshop activities (e.g. cleaning, tool management)

Complementary Description

Scopes and Accountabilities:

• Follows prescribed procedures, making alterations if needed, but must inform supervisor promptly; recommends expenditures. Divulging of confidential and/or sensitive information could lead to damage to reputation and/or competitive posture of the company. Errors may lead to high risk of major damage to the organization resulting in the need to create an entirely new approach.

Job Requirements

Requirements:

• ASNT Level II certification in FPI required. ASNT Level II certification in MPI, Eddy Current and Ultrasonic would be preferred.

• Airframe and Power Plant certificates issued by the FAA is preferred.

• Mechanical/technical/interpersonal skills which are adapted to the unique requirements of the organization

• Basic Level – Microsoft Office: Outlook, Word, Excel

• May be required to perform “On Call” duty on rotational basis

• Must be willing to work night shift either on a permanent or rotational basis

Physical Requirements:

• While performing the duties of this job, the employee is regular required to use hands to finger and frequently required to reach with hands and arms. The employee is occasionally required sit, stand, and walk.

• The employee must regularly lift and/or move up to 10 pounds and occasionally lift and/or move up to 25 pounds.

• Specific vision abilities required by this job include close vision, color vision, and ability to adjust focus.

• While performing the duties of this job, the employee will be working with chemicals that are unique to the processes being performed and will be required to wear the recommended personal protective equipment (PPE) when performing these processes.

Company Information

Safran is an international high-technology group, operating in the aviation (propulsion, equipment and interiors), defense and space markets. Its core purpose is to contribute to a safer, more sustainable world, where air transport is more environmentally friendly, comfortable and accessible. Safran has a global presence, with 100,000 employees and sales of 27.3 billion euros in 2024, and holds, alone or in partnership, world or regional leadership positions in its core markets.

Safran is in the 2nd place in the aerospace and defense industry in TIME magazine's "World's best companies 2024" ranking.

Safran Helicopter Engines is the world's leading manufacturer of helicopter engines, with more than 75,000 produced since being founded. It offers the widest range of helicopter turboshafts in the world and has more than 2,500 customers in 155 countries.

Locate your future workplace

2709 Forum DriveTX 75052

Grand Prairie

Texas United States

Safran is an Equal Opportunity Employer

All qualified applicants will receive consideration for employment without regard to race, color, sex, sexual orientation, gender identity, religion, national origin, disability, veteran status, or other legally protected status.

• Drive processes to continuously improve the business, enable next-generation manufacturing, and ensure compliance with all governing specifications, codes, and standards.
• Administer the facilities NDT Program, responsible for NDT duties to include processes, procedures, techniques, training, qualification, and certification.
• Experience in implementing or executing NDT processes, have a working knowledge of each technology and its strengths and limitations to ensure the proper inspection technique is used for the task.
• Ability to troubleshoot, provide technical leadership, and correct NDE processes while maintaining product and process flow.
• Serve as the primary liaison with customers on items of inspection.
• Understand and interpret codes, standards, specifications, and customer requirements related to NDE inspection to meet manufacturing demands and compliance.
• Develop and implement general inspection procedures and NDE method procedures and techniques.
• Perform site audits.
• Maintain effective communication and contact with Manufacturing and Quality to assure the operation of existing products into production.
• Accountable in support of new and existing product line inspection requirements.
• Consciously drive waste out of the NDT processes to increase quality and reduce inspection time and cost.
• Collaborate with the groups to assure the correct levels of NDT services used on new and existing products are appropriate for their use in the field.
• Continuously evaluate NDT processes to ensure the most appropriate techniques are being utilized and any new NDT techniques to improve throughput and cast are brought to fruition in a timely manner.
• Interface with manufacturing to ensure all NDT aspects of customer requirements are understood.
• Monitor and provide comprehensive reporting on the status of all NDT projects on a regular basis to all necessary parties requiring the information.
• Carry out other duties as and when business requirements dictate as may be reasonably expected.

• Minimum of 3 years of experience in support of manufacturing and quality as an ASNT NDT
• Must have a current level II UT certification - Non-Destructive Testing (NDT)
• Shearwave expereince highly preferred
• Computer literacy (including Microsoft Excel, Word, and Outlook)
• Forecast issues in advance to prevent potential impacts; both internally and externally.
• Able to define, work within and improve business processes based on immediate and future business needs.
• Confident and professional when representing the company in person and in writing.

Job Title: Non-Destructive Testing Technician

Job Description

We are seeking a skilled Non-Destructive Testing Technician to join our team. The position is available for four openings and involves working from 3:30 PM to 2 AM, Monday through Thursday. This role requires a professional who can conduct quality weld inspections and provide comprehensive reports in accordance with industry standards.

Responsibilities

• Conduct quality weld inspections using various methods in accordance with industry standards and contract specific requirements.

• Provide factual and comprehensive data, drafting reports that address NDT inspection criteria completely.

• Coordinate with Project Management, Production, Customers, and Third Party Surveyors as required.

• Prepare Quality Plans, Inspection, and Test Reports.

• Review and certify final documentation for customers.

• Demonstrate proficiency performance as a minimum NDT Level I / II with at least 600 logged hours in any two areas such as Visual, Dry Method, Wet Method, Gamma & X-Ray Radiography, Thickness & Shearwave Ultrasonic.

• Set up and perform NDT test procedures, interpreting specifications relative to NDT testing and acceptance/rejection criteria.

• Familiarize with the scope and limitations of the qualified methods and provide guidance to trainees.

• Prepare written instructions, organize, and report the results of examinations.

• Work independently and support team members.

• Perform other job-related tasks as needed.

Essential Skills

• Proficiency in NDT methods including VT, MP, PT, UT, RT.

• Certification to ASNT-TC-1A in at least two NDT methods such as Visual Examination, Liquid Penetrant, Magnetic Particle Testing, Radiographic Testing, Ultrasonic Testing.

• Previous Level II Certification to ASNT-TC-1A with documented classroom and on-the-job training experience.

Additional Skills & Qualifications

• Certified Level II Visual Examination, Liquid Penetrant, and Magnetic Particle Testing preferred.

• Current AWS Certified Welding Inspector (CWI) is a plus.

• Experience in inspecting metal fabrications, pressure vessels, piping, tanks, or gas systems.

• High School diploma or equivalent.

Why Work Here?

We offer competitive salaries along with profit sharing and a comprehensive benefits package for our team members. Benefits include health, dental, vision, life insurance, a 401(k) plan, tuition reimbursement, paid time off, holidays, a clothing program, a Wellness Program, and opportunities for career growth.

Work Environment

The technician will work under the direction of the Team Manager and will be responsible for safely producing quality parts in a timely manner. Our facility includes three large machining centers with potential growth opportunities in learning multiple different machining centers. The facility is clean and well-lit, with some buildings being temperature controlled while others are not.

Job Type & Location

This is a Permanent position based out of Cleveland, Ohio.

Pay and Benefits

The pay range for this position is $76900.00 - $11000.00/yr.

PLEASE ASK YOUR RECRUITER FOR A COPY OF THIS COMPANY'S BENEFITS OVERVIEW.

Workplace Type

This is a fully onsite position in Parma,OH.

Application Deadline

This position is anticipated to close on Sep 5, 2025.

About Aerotek:

We know that finding work is hard, and finding meaningful work is harder. Aerotek connects 180,000+ light industrial and skilled trades workers with 14,000+ employers each year, helping our workers navigate an evolving labor market and find jobs that meets their goals, skills and interests. Since 1983, we have provided a variety of career opportunities across North American industry - from short-term assignments at Fortune 500 companies where you can build your skills, to long-term opportunities where you can play a vital role solving for companies' construction, manufacturing and maintenance challenges. Our 1,500+ experienced recruiters across 250+ offices work relentlessly to put our workforce in a position to thrive. Let us rise to meet your challenges and put our people-are everything spirit to the test as your career continues to grow.

Aerotek offers weekly pay, employee benefits including medical, dental & vision, life insurance, health advocacy and employee assistance programs, a 401(k) plan, and employee discounts.

The company is an equal opportunity employer and will consider all applications without regards to race, sex, age, color, religion, national origin, veteran status, disability, sexual orientation, gender identity, genetic information or any characteristic protected by law.

Your Career Begins at Timken

If you're ready for a challenging career that provides you with the ability to advance personally and professionally, look to Timken. Our associates make the world more productive by improving the efficiency and reliability of the machinery that keeps industry in motion.

NDT Technician

Purpose: Perform non-destructive testing (NDT) inspections, operate chemical processes such as black oxide and passivation, and conduct quality related checks to ensure parts meet specified quality requirements.

This is a 2nd shift position, with regular hours of 3:00 p.m. to 11:00 p.m. Monday - Friday, plus overtime as needed.

What We Offer

• Competitive pay.

• Comprehensive benefits package including medical, prescription drug, dental, and vision insurance.

• Benefits start on first day of employment.

• Opportunities for career advancement.

• Supportive and team-oriented work environment.

Required Skills and Experience (Trainee):

• Minimum of 1 year experience in a manufacturing environment, or in a manufacturing trade (including technical school), preferably with metalworking/welding/machining exposure.

• Willingness to travel during the training phase for required classroom experience.

• Willingness to uphold strict product and process standards in accordance with aerospace requirements.

Preferred Skills and Experience (Technician):

• Magnetic Particle Inspection Level II certified per NAS410.

• In addition, Eddy Current, Nital Etch (surface temper etch), and Barkhausen Noise Test experience/certifications are preferred.

• NDT experience, in any additional techniques, preferred.

• Quality and/or inspection experience preferred.

• Laboratory experience with chemicals, titrations, and fluids analysis, preferred.

This role may be filled as either a trainee or technician, dependent upon experience, training, and certifications.

Responsibilities:

• Safety - daily participation and involvement in individual and team safety responsibilities such as Behavior Based Safety, housekeeping practices, chemical labeling, and proper use of Personal Protective Equipment (PPE).

• Assure that NDT inspections are accurate and performed in accordance with the applicable customer specifications.

• Perform diversified magnetic particle, surface temper etch, eddy current, and metallurgical inspection/tests on bearing components according to company specifications, requirements, and standards.

• Evaluate and properly identify testing indications and potential causes. Distinguish relevant from non-relevant indications.

• Mix and maintain all types of surface temper etch solutions including acids, bases, and cleaning solutions as required.

• Maintain NDT test equipment as required by specification, preventive maintenance plan, or customer requirement.

• Obtain in-process/finished bearings/parts from designated storage areas. Obtain sequence sheet and compare/check data against engineering drawing(s) for accuracy. Perform appropriate NDT tests/inspections on bearings/components, as required.

• Periodically perform chemical processing operations such as black oxide and passivation.

• Use various hand tools, fluorescent powder mixture, and acid base solutions/bath to conduct appropriate NDT tests.

All qualified applicants shall be treated equally according to their individual qualifications, abilities, experiences and other employment standards. There will be no discrimination due to gender or gender identity, race, religion, color, national origin, ancestry, age, disability, sexual orientation, veteran/military status or any other basis protected by applicable law.

The Timken Company, a global technology leader in engineered bearings and industrial motion, designs a growing portfolio of next-generation products for diverse industries. For more than 125 years, Timken has used its specialized expertise to innovate and create customer-centric solutions that increase reliability and efficiency. The company posted $4.6 billion in sales in 2024 and employs more than 19,000 people globally, operating from 45 countries. Timken has been recognized among America's Most Responsible Companies and America's Greatest Workplaces for Diversity by Newsweek, the World's Most Ethical Companies® by Ethisphere and America's Most Innovative Companies by Fortune.

Why Choose Timken?

• Over a century of knowledge and innovation

• A culture of top performance

• A global, diverse environment

• Products that contribute to a sustainable world

• A conviction to improve communities around us

• Competitive salary and benefits

Not Ready To Apply?

Stay connected by joining our network and we'll keep you informed about upcoming events and opportunities that match your interests.

Talent Community

Job DescriptionJob DescriptionThis position is responsible for processing and evaluating welded and machined components using the Fluorescent Penetrant Inspection method to MB Aerospace East Granby procedures along with customer specifications.

This position sits in Warren, MI and will report to the Quality Manager.
Culture
About Us
MB Aerospace is an international group providing complex engineering solutions to some of the key names in the Aerospace and Defense market. Operating from sites close to our key customers in North America, Asia and Europe, the MB Aerospace group provides advanced technological solutions to the Aerospace and Defense industry, leveraging an in-depth knowledge of fabrications, machining and the global supply chain to support complex aero-engine component manufacture and repair.
Responsibilities
Key Responsibilities

• Review and implement customer requirements; such as: Engineering Drawings, Process Specifications and other industry standards. Develop and maintain processes, test methodology and procedures. Understand manufacturing methods and part construction, as it relates to the NDT data.
• Operate X-ray equipment and interpret film
• Oversee and process OE & repair/overhaul hardware through FPI line and interpret results
• Perform process control checks and NDT related calibrations as necessary
• Identify and investigate new technologies, processes and/or procedures to maintain or improve NDT capabilities, efficiencies, etc.
• Interface with engineers, internal customers, manufacturing personnel and management to improve processes. Provide guidance, leadership and instruction to other NDT technicians.
• Integrate improvements to realize benefits in cost, cycle, and customer satisfaction.
• Perform other assignments and tasks as directed.
• Ensure adherence to applicable MB Aerospace internal, federal, state and local laws and regulations related to compliance and takes responsibility to ensure ongoing conformity with such rules and regulations

Job Requirements

• Associate Degree of Applied Science in NDT - The classroom training for the applicable test method and level of certification needed must meet the minimum required per NAS-410
• 4 years work experience in the NDT method(s) and manufacturing processes; certified Level 2 is .
• Employee must have the skills and formal training needed to become certified to NAS 410 level 2 in radiography testing (RT) and Penetrant Testing (PT) and be able to pass an annual eye examination per the requirements of NAS 410.
• Must have a thorough knowledge of NDT theory, methods and procedures, and should have knowledge of NDT technologies, computer systems and conventional and automated testing systems.
• Make and keep precise measurements and keep accurate records.
• Must be able to take instructions and offer advice. The ability to work well with supervising engineers, other technicians, and mechanics is essential because technicians interact with people from other divisions, businesses, and customers.
• Experience applying principles of mathematics for analysis, design, and troubleshooting tasks in their work.
• Operating a personal computer with proficiency in related technical and specialized software. Extensive knowledge of Microsoft Office (Excel, Word, Powerpoint, Access, Outlook, etc)
• Must comply with ITAR regulations and site SSA requirements.
• Must have unrestricted authorization to work in the USA.

MB Aerospace is an Equal Opportunity Employer. MB Aerospace is a subcontractor to the United States Government and provides defense services involving technical data and products governed by the Arms Export Control Act and the International Traffic in Arms Regulations (ITAR), 22 C.F.R. parts 120 - 130 and the Export Administration Act and the Export Administration Regulations (EAR), 15 C.F.R. parts 730 – 774 (“Export Laws”). All candidates are subject to review and governance under such Export Laws and any offer of employment may be subject to additional considerations and/or conditions.

MB Aerospace is An Equal Opportunity/Affirmative Action Employer. All qualified applicants will receive consideration for employment without regard to , , , , , , , or veteran status, or any other federally protected class.
Requirements
High School / GED Completed
Authorized to work in the US without sponsorship
Accept a background check to be performed
Accept a drug test to be performed
1-4 years NDT Experience
Equal Opportunity Employer
Barnes Aerospace provides equal employment opportunities to all employees and applicants for employment and prohibits discrimination and harassment of any type without regard to , , , , , , status, genetics, protected veteran status, , or expression, or any other characteristic protected by federal, state or local laws.

Requisition #clsvwmq58wm7g0rmkgpz7jnw0

Job DescriptionJob Description

MUST already have NAS-410 Certification and proof of UT hours (Signed off by a Level III NDI).  

Must have level I  and Level II training (proofs) plus an additional 800hrs. minimum of UT. 

Candidate has to provide Proof of Training and OJT for Level II Ultrasonic NAS410 Certification, Signed Off by a Level III NDI

Ultrasonic phased array, automated immersion,  automated modified immersion and manual phased array.

Hands on experience on Non-Destructive inspection methods  (ultrasonic)

Experience with Graphite Composites in relation to Aerospace.  
 

• Responsible for using analysis techniques to evaluate the properties of a materials, components or systems without causing damage.
• Utilize Non-Destructive inspection methods (liquid penetrant, magnetic particle, thermography, shearography, eddy current, ultrasonic, radiography) to verify parts and processes are in compliance with customer engineering requirements.
• Set-up and standardize NDI equipment, process parts, interpret and evaluate for acceptance or rejection, and document results. Establish techniques from approved general procedure or work instructions for final approval. Conduct system performance checks in accordance with applicable process standards.
• Provide necessary guidance and/or supervision to trainees. Perform audit surveillance on non-destructive inspection processes and initiate and document any non-conformances according to specification, process and procedures.
• Interpret codes, standards, and other contractual documents that control NDT methods. Assume technical responsibility for the NDT facility, equipment and staff. Prepare, verify and approve procedures and work instruction for technical adequacy. Provide training, examination, and certification of personnel.
• Perform audit surveillance on non-destructive inspection processes and initiate and document any non-conformances according to specification, process and procedures.

POSITION SUMMARY

Non-destructive testing (NDT) technicians/specialists perform non-destructive tests on aircraft structures and components for flaws that could affect the aircraft or component with regard to airworthiness. The testing processes do not damage the structure or object being tested. Technicians look for corrosion, cracks and flaws which might lead to failure of the components.

JOB RESPONSIBLITIES

1. Ensure that all non-destructive testing is performed in accordance with manufacturer's specifications.
2. Ensure that all non-destructive testing equipment is in proper working order and in current calibration at all times.
3. Performs NDT inspection of aircraft, engines, propellers, accessories, components and materials processed through the repair station.
4. Ensures proper documentation of discrepancies on appropriate forms, work orders, tags or aircraft logs.
5. Ensures that shift turnover procedures are followed and properly documented.
6. Complies with repair station procedures and company policies.
7. Properly certificated in accordance with FAR 65, Subpart D or E, and will meet the applicable personnel qualification/certification requirements of the FAA approved EAMS NDT process specification EMBNDT002.

ESSENTIAL KNOWLEDGE, SKILLS AND ABILITIES

Education:

• High School Diploma, A.S. Degree in Aviation preferred
• A&P Certificate
• Level II NDT certification preferred

Experience:

• Generally, 8 years and experience in NDT inspection

Knowledge, Skills & Abilities:

• Assignments require Comprehensive Knowledge of all possible tasks and responsibilities within their Technical Area
• Skills are broadly applied in multiple Technical Areas.
• Knowledge of safety and operating procedures for power-on aircraft
• Ability to understand procedures, acting in problem solving, suggesting improvements.

Working Conditions / Environment/ Special Requirements

• Ability to work in a safe professional manner adhering to all regulatory requirements including, OSHA, EPA, State and Federal regulations.
• As required by the position, must have the ability to wear a respirator as per OSHA 29 CFR 1910.134 "Respirator Protection" regulations with no restrictions that would prevent the proper use and/or seal of the respirator.
• Ability to work flexible hours and different shifts if required.
• Employees will be subject to the random drug and alcohol testing under FAA regulations.
• Must have successfully completed a vision exam prior to any training.
• This employee is subject to an annual vision test.

Embraer is an Equal Opportunity Employer.

• Perform MT, PT, UT, RT, and VT examinations. Interpret results and prepare reports documenting results.
• Maintain certification in MT, PT, UT, RT, and VT inspection techniques.
• Maintain current procedures and equipment calibrations for the NDT department.
• Maintain client contact for ongoing projects and interface with the NDT manager to prepare proposals, schedule laboratory and field testing activities.
• Assist coordination of full-time and intermittent field projects by AET personnel, including reporting and invoicing.
• Maintain client contact for ongoing projects and interface with the NDT manager to prepare proposals, schedule laboratory and field testing activities.
• Assist in the promotion and marketing of AET and the NDT department.
• Training to obtain and maintain certifications. Stay abreast with current NDT technologies utilized by AET.
• Conduct field, laboratory and office activities in a manner consistent with federal, state, and local regulations, along with AET's QA and Health and Safety Policies, to promote the safety and protection of employees, clients and the public.
• Ability to interact successfully with a wide variety of people, work effectively within project teams, resolve issues and problems in a constructive manner, and work independently in the field.

• None

• High school diploma or equivalent.
• Maintain valid driver's license and acceptable driving record. Some positions may require use of personal vehicle for company business. Maintain compliance with DOT driver regulations if required for position. Maintain appropriate physicals if required for position.
• Ability to meet the requirements for Assistant Radiographer and be working toward ASNT-TC-1A for UT, MT, PT, and RT methods.

• Associate Degree in Non-Destructive Testing Technology or Welding Certification.

• Occasionally move 50-70 pounds.
• Stand up to 80% of the day (often on uneven surfaces).
• Move up to 80% of the day, with frequent climbing, bending and stooping.
• Occasionally work in confined spaces.
• Occasionally work at elevations up to 200 feet, using proper safety equipment as necessary.